Full Vent Rebuild & Replacement in Austin, TX
Vinyl and foil flex inside walls, corroded seams, crushed sections behind the drywall, joints held by screws that snag a fresh layer of lint every load — some ducts are past saving. We remove the old run entirely and rebuild it in smooth rigid metal along the existing route: sections joined in the direction of airflow, sealed with foil tape, supported so they can't sag into lint traps, finished with a new termination hood and a listed transition connection at the dryer. It is the difference between renting your problem back every year and retiring it. Before/after airflow readings document the change. Serving Austin (60 ZIP codes, 975k residents) and surrounding neighborhoods with same-week scheduling.
Full Vent Rebuild & Replacement in Austin
A full rebuild replaces the entire exhaust duct — not just the visible ends — with new, code-compliant material along the existing route. It is the fix for ducts that are wrong by construction: vinyl or foil flex buried in walls, rusted-through seams, sections crushed during a past remodel, or joints assembled with screws that have been combing lint out of the airstream for a decade. Cleaning a duct like that is renting the problem back annually. Rebuilding it in smooth rigid metal, joined with foil tape and supported so it cannot sag, retires the problem: the new duct sheds lint instead of hoarding it and holds airflow year after year.
Local dossier · Austin, TX
Austin remodels everything — and dryer vents pay for it. A Crestview or Allandale ranch that's been opened up twice since 1965 often has a duct nobody currently alive has seen: rerouted around a kitchen island here, extended past a new bathroom there, terminating wherever the last crew found daylight. East side bungalows add garage conversions and backyard ADUs with stackable units vented through whatever wall was nearest. Meanwhile the new construction — Mueller, the condo stacks along the lake — brings the opposite problem: tight, efficient envelopes where a closed laundry closet starves the dryer of makeup air and long engineered runs need every foot accounted for. Our Austin work leans hard on the camera: in a city this renovated, the inspection isn't a formality, it's the only honest way to know what's in the wall. Then we fix exactly that, to code, with the math shown.
Texas State Capitol
Common signs in Austin homes
- Your duct is shiny foil or white vinyl flex, especially inside walls or the attic
- Rust flakes or metal debris appear in the lint you clean out
- Airflow stays weak even immediately after a professional cleaning
- A camera inspection found crushed sections, gaps, or screws inside the duct
- The house predates the 1990s and the vent has never been replaced
- Moisture or lint stains appear along the duct's path through the house
Full Vent Rebuild & Replacement in Austin (Travis County) — what's local
Austin sits in Travis County (county seat: Austin). For full vent rebuild & replacement that means our Austin crew sizes up the local housing stock before quoting — and follows Travis County permit requirements for any work that needs an inspection sign-off.
Built to code · Full Vent Rebuild & Replacement in Austin
Full Vent Rebuild & Replacement is held to published national standards no matter the city. Our Austin crew builds to these and documents the work; the locally-adopted code edition and permit requirements are confirmed with Travis County's authority on every job.
- IRC M1502 — Dryer exhaust ducts must be smooth-interior rigid metal, minimum thickness, with joints fitted in the direction of airflow and no fasteners protruding into the airstream.
- Manufacturer install manuals — Dryer makers specify duct type, diameter, and maximum run for their machines — a rebuild is matched against your specific dryer's manual, not a generic assumption.
Scoped from a camera inspection
At Prime Dryer Vent Experts, a full vent rebuild & replacement is never guesswork. We scope every job from a camera vent inspection first — mapped route, measured developed length against IRC M1502, and airflow readings — so the work is matched to what your duct actually needs, with the report to prove it. The documented inspection is the record the full vent rebuild & replacement is built on.
Camera vent inspection in AustinEvery full vent rebuild & replacement in Austin
Deliverables
- Old duct removed and hauled away
- New rigid metal run, taped joints, correct slope and support
- New termination hood with working backdraft damper
- Before/after airflow readings and full photo set
How a job runs
Scope and access plan
Using camera findings, we map the failed run and plan the minimum wall or ceiling access needed to replace it cleanly.
Removal
The old duct comes out in full — flex, failed sections, illegal materials — and is hauled away, not abandoned in the cavity.
Rebuild in rigid metal
New smooth-interior metal duct is installed, joints crimped in the airflow direction, foil-taped, and supported against sagging.
Termination and transition
A new exterior hood with backdraft damper goes on, and a listed transition duct connects the dryer.
Close-up and verification
Access openings are patched paint-ready, airflow is re-measured under load, and the photo record is delivered.
8+ neighborhoods in Austin
Same-week service across every neighborhood in Austin. Don't see yours? Call (XXX) XXX-XXXX — if it's in Austin, we cover it.
The Austin advantage.
Our Austin crew lives in the metro they serve, across Travis County. They know which Austin neighborhoods — Tarrytown, Hyde Park, Travis Heights and more — have long, lint-packed duct runs, and which newer builds hid the transition hose in the wall. Local code knowledge, local referrals, local accountability for every full vent rebuild & replacement.
More services in Austin
Full Vent Rebuild & Replacement in nearby Travis cities
We cover full vent rebuild & replacement across Travis County — same crew, same warranty. Nearby Austin cities we also serve:
Full Vent Rebuild & Replacement in Austin — FAQ
My duct is foil flex inside the wall — is that really a problem?
Yes. Ribbed foil traps lint along every corrugation, crushes easily, and isn't permitted as the concealed dryer duct under the residential code. It's the most common defect we find in homes from the 1970s through the 1990s. Rebuilding in smooth rigid metal retires the problem permanently.
How disruptive is a full rebuild?
Typically half a day to a full day. We plan access from the camera findings first, so walls open only where the duct actually needs replacing. Old material is hauled out, new rigid metal goes in, openings are patched paint-ready, and the final airflow reading goes on your report.
My Austin home has been remodeled — how do I know where the dryer duct even goes?
You probably can't from the outside, and that's normal here. Our camera inspection traces the actual route through the structure, documents materials and condition, and maps where it terminates. Austin's remodel layers make this the highest-value $89 in the system — it turns guesses into a diagram.
My condo's dryer takes forever. Is that the building's fault?
Often, partly. Mid-rise and condo runs are long by necessity, and some legitimately need a listed booster fan. Closed laundry closets also starve dryers of makeup air. We measure back-pressure and airflow, then give you — and if needed, your HOA — a written verdict on which factor is doing the damage.
Does an ADU or garage-conversion dryer need its own vent?
Yes — a full, code-compliant exhaust to the outdoors, same as the main house. We regularly find conversion units venting into attics or crawlspaces, which dumps flammable lint and moisture into the structure. A short, correctly terminated run is usually simple to install; venting indoors is never acceptable.
Do you serve all of Austin?
Yes — our crews cover Austin's 60 ZIP codes across Travis County, including Tarrytown, Hyde Park, Travis Heights, plus the surrounding communities.
How soon can you schedule full vent rebuild & replacement in Austin?
We offer same-week scheduling across Austin, booked by a real person in under two minutes, 7 AM to midnight every day.
How much does full vent rebuild & replacement cost in Austin, TX?
Full Vent Rebuild & Replacement in Austin starts from $450, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A licensed & insured technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (XXX) XXX-XXXX for a free, no-pressure Austin quote.
Do you offer emergency or same-day full vent rebuild & replacement in Austin?
Yes — we run same-week and emergency full vent rebuild & replacement across Austin, scheduled by a real person 7 AM to midnight every day. For an active dryer-vent hazard, call (XXX) XXX-XXXX and we prioritize Austin dispatch so a craftsman is on it fast.
Is there a licensed & insured full vent rebuild & replacement company near me in Austin?
Our Austin crew lives in and works the metro across Travis County, including Tarrytown, Hyde Park, Travis Heights — a certified, local full vent rebuild & replacement team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (XXX) XXX-XXXX.
Last reviewed:
Get it inspected. Get it in writing.
Flat fee confirmed when you book. Same-week scheduling. A pass/fail verdict within 48 hours.
24/7 Response
No airflow, overheating dryer, burning smell, or a vent you're not sure about? We answer 7 AM to midnight and the assessment ends in a written safe-to-use verdict — including a do-not-use notice when the evidence supports one. After-hours dispatch runs subject to crew availability.
Emergency line